New pages
- 22:08, 15 May 2024 (valve) is too busy! (1 pending operations) (hist | edit) [1,577 bytes] Jim.Wilson (talk | contribs) (Created page with ":'''<valve> is too busy! (1 pending operations)''' This error message may be displayed when the CEGS application is restarted after an unexpected shutdown. The error is raised when a solenoid valve is in an unexpected state. Almost always, this occurs when the software valve state is opened but the physical valve is actually closed. The easiest way to correct the problem is to interact with the application user interface to "close" the valve. A possible complic...") Tag: Visual edit: Switched
- 16:13, 14 May 2024 GR TC Tip Creation (hist | edit) [419 bytes] 73.24.216.92 (talk) (Created page with "* Cut a blank out of SS304 tube 1/8 x 035 seamless that is ~.540 * Face part to (.500-.525) * Chamfer both faces * Use .065 bit to drill 3/16 into the part * Chamfer by using a #00 bit * Turn the wheel on the arm so that the bit is sticking out by less than half an inch * Put the bit deep into the collet * Touch the bit to the part * Tap with a M1.6 x .35 * Clean the part * Crush the back half of the part in a vice")
- 18:28, 9 May 2024 GR TC Tip (hist | edit) [0 bytes] 73.24.216.92 (talk) (Created page with "* Cut a blank that is .550 * Face part (.500-.525) * Use .065 bit to drill 3/16 into the part * Chamfer by using a #00 bit * Turn the wheel on the arm so that the bit is sticking out by less than half an inch * Put the bit deep into the collet * Touch the bit to the part * Tap with a M1.6 x .35 * Crush the back half of the part in a vice")
- 14:57, 3 May 2024 Plug Valve 1/4 + Actuator Creation (hist | edit) [1,734 bytes] 73.24.216.92 (talk) (Created page with " =Insert the valve stem into the coupling= #Choose the plug's orientation in the coupling according to the valve's intended location in the plumbing Notes: #The actuator is pre-programmed to the closed position. #Usually, the servo connector pins should point downstream, and the plug's port-sealing O-ring should face upstream. #Thus, the port O-ring usually faces away from the servo pins. Exceptions occur when the downstream chamber volume must be minimized. #Align the h...")
- 20:43, 2 May 2024 Blow gun with 1/8 OD x 9" nozzle Creation (hist | edit) [255 bytes] Jim.Wilson (talk | contribs) (Created page with "# Drill a .120 hole in the end of the blow gun. # Widen the hole with a 1/8" undersized reamer. # Cut a 9" piece of SS304 tube 1/8 x 035 seamless. # Clean off the burr from the inside and outside of the tube. # Press the tube into the tip of the blow gun.")
- 20:33, 2 May 2024 GR furnace arm (hist | edit) [386 bytes] Jim.Wilson (talk | contribs) (Created page with "# Remove any plastic covering or glue from the furnace arm blanks # Tap the bottom hole with a 6/32" tap # Widen the large hole using an oversize 3/8" reamer in the mill #* set the vice so that the arm is secured but held only loosely by the vice; it is important that the reamer is able to center itself in the hole to avoid damaging the tool #* set the mill to slow speed and use oil.")
- 17:01, 25 April 2024 O-ring bakeout Creation (hist | edit) [1,038 bytes] 73.24.216.92 (talk) (Created page with "O-ring bakeout Summary: Bake Viton O-rings at 150 °C under vacuum for 4 hours. Distribute the O-rings evenly in a clean borosilicate or stainless steel vessel. A dish or pan is best. A beaker may be used for smaller quantities of O-rings, but spreading the O-rings over a larger surface area is preferable. Place the O-rings into the vacuum oven and evacuate the chamber to < 7 Torr. If the bakeout vacuum system is equipped with a turbo pump and flow-through cold trap,...")
- 17:21, 23 April 2024 TC Staple Creation (hist | edit) [309 bytes] 73.24.216.92 (talk) (Created page with "# Cut SS304 wire 0.025 spring back to 1.625 inches. # Grab the center of the cut wire with pliers. # Bend the wire down on both sides of the pliers. #* If the wire was centered correctly then both legs of the wire will be the same length. #* Check model to make sure that the part is made to the correct size.")
- 17:17, 23 April 2024 MFV Actuator Adapter Creation (hist | edit) [302 bytes] 73.24.216.92 (talk) (Created page with "# Cut blank to .504 # Face part on the lathe # Use center bit to put a mark on part # Use .182 bit to create hole at center # Chamfer the inside edge of both sides of the hole # Ream the part with a 3/16 undersized bit # Grind .015 off the side of the part # Drill a .136 hole # Tap that hole with 8-36")
- 17:13, 23 April 2024 Phase Separator Rod Creation (hist | edit) [582 bytes] 73.24.216.92 (talk) (Created page with "# Cut rod to 14.084 # Use swagelok bender # Mark the part 6.071 from the end #* We will call this section of the rod leg a # Place leg a in the bender and line up the mark on the rod with the 0 mark on the bender # Make a 90 degree bend # Check to make sure it is square")
- 13:42, 23 April 2024 CEGS Nameplate Creation (hist | edit) [1,323 bytes] 73.24.216.92 (talk) (Created blank page) Tag: Visual edit
- 18:48, 22 April 2024 CCA U6 Interface (hist | edit) [0 bytes] Tyler (talk | contribs) (Created blank page)
- 16:58, 18 April 2024 Servo Spacer-Bearing Creation (hist | edit) [172 bytes] 73.24.216.92 (talk) (Created page with "# Place a .144 bit in the mill. # Turn the mill on then push the spacer-bearing onto the drill bit. #* MAKE SURE TO NOT TOUCH THE BIT WITH HANDS OR ANY LOOSE CLOTHING/HAIR.")
- 18:03, 16 April 2024 Grounding Kit Creation (hist | edit) [974 bytes] AddisonSterner (talk | contribs) (Created page)
- 18:21, 4 April 2024 Viton Tubing 189 x 125 x 350 Creation (hist | edit) [487 bytes] Tyler (talk | contribs) (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/a35715b31e1144bc0aa06498/w/c8226b87bcb011f2fffb5a31/e/238974ab5a9f323bb71322f0?configuration=default&renderMode=0&uiState=65da8b25a559230a8b1bf414 |about=Viton_Tubing_189_125_350 |product=Viton+tubing+189+x+125+x+350}} # Use a short length (< 3") of stock. # Press the stock onto the mandrel until the end is flush with the stop. # Part the stock with a razor. # Remove the finished part from...")
- 18:02, 4 April 2024 Viton Tubing 189 x 125 x 350 (hist | edit) [340 bytes] Tyler (talk | contribs) (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/a35715b31e1144bc0aa06498/w/c8226b87bcb011f2fffb5a31/e/238974ab5a9f323bb71322f0?configuration=default&renderMode=0&uiState=65da8b25a559230a8b1bf414 |creation=Viton_Tubing_189_125_350_Creation |product=Viton+tubing+189+x+125+x+350}} Used as the gasket for a Port Pressure Sensor.")
- 17:56, 4 April 2024 Port Pressure Sensor (hist | edit) [445 bytes] Tyler (talk | contribs) (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/a35715b31e1144bc0aa06498/w/c8226b87bcb011f2fffb5a31/e/238974ab5a9f323bb71322f0?configuration=default&renderMode=0&uiState=65da8b25a559230a8b1bf414 |creation=Port_Pressure_Sensor_Creation |product=port+pressure+sensor+30+psi}} A pressure sensor modified to be inserted directly into the plumbing, provides a typical pressure range of 0 to 30 psi, with a resolution of 0.1 Torr.")
- 17:11, 4 April 2024 Port Pressure Sensor Creation (hist | edit) [499 bytes] Tyler (talk | contribs) (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/a35715b31e1144bc0aa06498/w/c8226b87bcb011f2fffb5a31/e/238974ab5a9f323bb71322f0?configuration=default&renderMode=0&uiState=65da8b25a559230a8b1bf414 |about=Port_Pressure_Sensor |product=port+pressure+sensor+30+psi}} # Add the spacer port pressure sensor to the pressure sensor. # Push the spacer all the way down. File:port_pressure_sensor_render.png|alt=a render of a finished port pressure sensor.|thumb|A render of a...") Tag: Visual edit: Switched
- 20:30, 2 April 2024 Plumbing Assembly Creation (hist | edit) [1,155 bytes] 73.24.216.92 (talk) (Created page with " #*KEEP AS STRAIGHT AS POSSIBLE FOR EASIEST TIME #*Use model to layout assembly before hand #*Will need different lengths of small tubes and swegg tees, elbows, and crosses #*Plan which pieces are going to be attached first for easiest assembly using vice #Use copper jaws or weaker vice grip to not mark plumbing #Hold plumbing on swegg and part number sides, dont attach vice on the nuts #Grab tee holders and swegg wrench (9/16 wrench--> 1/4 & 7/8 wrench--> 1/2) #Assure t...")
- 19:31, 2 April 2024 Purge Gas Supply Line (hist | edit) [3,853 bytes] Jim.Wilson (talk | contribs) (Created page with "== Introduction == This is a maintenance procedure for purging a gas supply line to the CEGS. This procedure must be performed for each process gas during installation. It should be repeated whenever there is any reason to suspect the purity of the gas reaching the CEGS. For example, whenever the gas cylinder is changed or if the gas supply tubing has been opened to atmosphere. This procedure assumes the user is familiar with the CEGS and its operation. === A note abo...")
- 18:01, 29 March 2024 PS Terminal Guard Creation (hist | edit) [687 bytes] AddisonSterner (talk | contribs) (Created page)
- 18:32, 22 March 2024 Solenoid Valve Stack Creation (hist | edit) [302 bytes] 73.24.216.92 (talk) (Created page with "#Take the black stop off of the solenoid valve 1/8 FPT 120 VAC 3 way stackable. #Before connecting the valves attach all of the needed adapters and plugs to valves. #Press the stack on top of a flat surface and up against a long straight object when tightening the valves together.")
- 18:41, 14 March 2024 Heater Controller Calibration (hist | edit) [3,272 bytes] Jim.Wilson (talk | contribs) (Created page with " == Setup == === Set up the hot point reference furnace ("CALHC") === # Mount a ceramic fiber furnace with a potted thermocouple on a lab stand. #* Use a furnace prepared as for CCS heater. # Insert a secondary Type K thermocouple ("tCal") into HPR, end-to-end with HPR's potted thermocouple. #* tCal's cable must be fitted with a miniature-style thermocouple connector. #* Use the dimpled thermocouple coupling tube to keep the tips thermally connected...")
- 14:41, 13 March 2024 Configuring a HACS Host Computer (hist | edit) [4,459 bytes] 73.24.216.92 (talk) (Created page with "== Windows OOBE (out of box experience) == Do not connect to the internet during the initial Windows setup (the Windows OOBE). Select desired language & keyboard layout(s). If the "I don't have internet" option is not visible, press <code>Shift+F10</code> to open command prompt. If you've previously connected to a network, enter: <code>netsh wlan delete profile name=* i=*</code> to remove known networks. Enter: <code>oobe\bypassnro</code> to restart the OOBE. You wil...")
- 14:08, 12 March 2024 CO2 Cylinder Creation (hist | edit) [802 bytes] 73.24.216.92 (talk) (Created page with "== Remove the label == # Peel off the clear plastic label cover # Use a razor blade to scrape off the paper, leaving only adhesive behind # == Vent the CO2 outdoors using yellow tool == Machine the opening on the lathe") Tag: Visual edit: Switched
- 22:01, 28 February 2024 Ion Gauge Service (hist | edit) [6,733 bytes] Jim.Wilson (talk | contribs) (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/964b8a00cc64089da952f896/w/3803982953276ca2551977d6/e/e25fb30d1907a1fa5aefd5aa?renderMode=0&uiState=65dfe043b5d43f6bd73a371a |about=Pressure Sensor AIM-X |product=pressure+sensor+AIM-X}} This is a maintenance procedure for servicing an Edwards AIM ion gauge, a commonly-used high-vacuum pressure sensor. AIM stands for Active Inverted Magnetron. It is a cold-cathode type of ion gauge. This service is required typicall...")
- 21:04, 24 February 2024 Port Pressure Sensor 100 PSI No Spacer (hist | edit) [367 bytes] Anna.b (talk | contribs) (added nav bar and links, inserted information about the product, applied markup text)
- 20:59, 24 February 2024 Port Pressure Sensor 100 PSI No Spacer Creation (hist | edit) [760 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending)
- 20:47, 24 February 2024 Port Pressure Sensor 100 PSI (hist | edit) [359 bytes] Anna.b (talk | contribs) (added nav bar and links)
- 20:42, 24 February 2024 Port Pressure Sensor 100 PSI Creation (hist | edit) [535 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending)
- 20:25, 24 February 2024 Phase Separator Pad (hist | edit) [320 bytes] Anna.b (talk | contribs) (added about this item link to nav bar, and short info)
- 20:22, 24 February 2024 Phase Separator Pad Creation (hist | edit) [838 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending)
- 20:05, 24 February 2024 Phase Separator Frame (hist | edit) [348 bytes] Anna.b (talk | contribs) (added nav bar and links, added small summary)
- 20:03, 24 February 2024 Phase Separator Frame Creation (hist | edit) [395 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending)
- 19:41, 24 February 2024 Servo Serial (hist | edit) [279 bytes] Anna.b (talk | contribs) (added nav bar and links)
- 18:52, 24 February 2024 Servo Serial Creation (hist | edit) [8,941 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending, pending instructional images.)
- 18:08, 24 February 2024 Servo CPW (hist | edit) [251 bytes] Anna.b (talk | contribs) (added nav bar and links)
- 17:23, 24 February 2024 Servo CPW Creation (hist | edit) [4,343 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending, pending instructional images.) Tag: Visual edit: Switched
- 14:18, 24 February 2024 VTC Heater (hist | edit) [1,166 bytes] Anna.b (talk | contribs) (added nav bar and links, inserted information about the product, applied markup text)
- 14:14, 24 February 2024 VTC Heater Creation (hist | edit) [4,463 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending, pending instructional images.)
- 13:20, 24 February 2024 VTC (hist | edit) [9,814 bytes] Anna.b (talk | contribs) (added nav bar and links, inserted information about the product, applied markup text) Tag: Visual edit: Switched
- 13:09, 24 February 2024 VTC Creation (hist | edit) [2,759 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending, pending instructional images)
- 20:17, 23 February 2024 CP21xx Serial Programming (hist | edit) [1,851 bytes] 73.24.216.92 (talk) (Created page with "Windows is unable to uniquely identify multiple devices that have the same VID (vendor ID) PID (product ID) and Serial number. All CP210x USB to UART Bridge Controllers come with a Serial number of 0001 by default. We update this Serial number to a unique value, so Windows can easily identify which device should be assigned to each COM port. Instructions Ensure the CP210x Universal Windows Drivers are installed. Open the '''CP21xx Customization Utility''' Insert a CP...") Tag: Visual edit
- 23:37, 20 February 2024 Fabricated Parts (hist | edit) [271 bytes] Jim.Wilson (talk | contribs) (Created page with "These parts are made, at least in part, by bending or forming material into a new shape. * LN valve stem * VTC drain * FTC drain * FTC LN line * inline LN phase separator funnel * inline LN phase separator shroud * phase separator rod * TC staple * VTC heater insulation")
- 23:33, 20 February 2024 Modified Parts (hist | edit) [941 bytes] Jim.Wilson (talk | contribs) (new page. needs editing to distinguish between commercially available and custom parts.)
- 23:30, 20 February 2024 Other Machined Parts (hist | edit) [624 bytes] Jim.Wilson (talk | contribs) (Created page with "These simpler parts generally requiring only cutting, sawing, drilling, punching and grinding operations. * aluminum 6061 rod 250 x 2 * aluminum 6061 rod 250 x 2.75 * actuator frame bearing blank * frit inlet port trap 250 * FTC bank bar * GR bank hinge * GR swing stop * LN manifold spring * RENC wire * screw 4-40 x 1-9/16 PH SS * screw 4-40 x 15/16 PH SS * screw 4-40 x 2-3/16 PH SS * FTC air line * GR furnace arm sleeve * LN tube sleeve 250 * LN vent snubber * phase se...")
- 23:28, 20 February 2024 Turned Parts (hist | edit) [369 bytes] Jim.Wilson (talk | contribs) (Created page with "Aeon produces these parts primarily on a CNC lathe: * LN supply flow restrictor 076 * LN supply flow restrictor 082 * LN valve stem * LN valve stem collar * SS316 EP tubing 250 x 035 x 1.184 * SS316 EP tubing 250 x 035 x 1.224 * SS316 EP tubing 250 x 035 x 1.477 * SS316 EP tubing 250 x 035 x 1.5 * SS316 EP tubing 375 x 035 x 1.316 * SS316 EP tubing 500 x 035 x 1.799")
- 23:26, 20 February 2024 Milled Parts (hist | edit) [1,132 bytes] Jim.Wilson (talk | contribs) (New page) Tag: Visual edit
- 19:30, 18 February 2024 O-Ring .5x.125 (hist | edit) [225 bytes] Anna.b (talk | contribs) (added nav bar and links)
- 19:29, 18 February 2024 O-Ring .5x.125 Creation (hist | edit) [756 bytes] Anna.b (talk | contribs) (Added instruction info, markup lang, link nav bar, updated product info link; about this item still pending; removed 3D model from nav since no link exists) Tag: Visual edit: Switched