User contributions for 73.24.216.92

15:5715:57, 15 May 2024 diff hist 0‎ Actuator Frame 4PV Creation ‎No edit summary current

18:0618:06, 14 May 2024 diff hist +603‎ Actuator Frame Bearing Blank Creation ‎ new method current Tag: Visual edit
17:4317:43, 14 May 2024 diff hist +58‎ CEGS Creation ‎ →‎Meters - Preliminary Settings: Added nominal values for 30 PSI sensors current
17:2217:22, 14 May 2024 diff hist +108‎ CEGS Creation ‎ →‎Integration: Edited the Gas Supply Tests section with more specific instructions for the Test() function
16:1316:13, 14 May 2024 diff hist −402‎ GR TC Tip ‎ Blanked the page current Tag: Blanking
16:1316:13, 14 May 2024 diff hist +419‎ N GR TC Tip Creation ‎ Created page with "* Cut a blank out of SS304 tube 1/8 x 035 seamless that is ~.540 * Face part to (.500-.525) * Chamfer both faces * Use .065 bit to drill 3/16 into the part * Chamfer by using a #00 bit * Turn the wheel on the arm so that the bit is sticking out by less than half an inch * Put the bit deep into the collet * Touch the bit to the part * Tap with a M1.6 x .35 * Clean the part * Crush the back half of the part in a vice" current

12:5812:58, 10 May 2024 diff hist +41‎ GR TC Tip ‎No edit summary

18:5418:54, 9 May 2024 diff hist +21‎ GR TC Tip ‎No edit summary
18:2818:28, 9 May 2024 diff hist +340‎ N GR TC Tip ‎ Created page with "* Cut a blank that is .550 * Face part (.500-.525) * Use .065 bit to drill 3/16 into the part * Chamfer by using a #00 bit * Turn the wheel on the arm so that the bit is sticking out by less than half an inch * Put the bit deep into the collet * Touch the bit to the part * Tap with a M1.6 x .35 * Crush the back half of the part in a vice"

14:1614:16, 8 May 2024 diff hist +75‎ CEGS Creation ‎ →‎Removal Procedure
14:0414:04, 8 May 2024 diff hist +132‎ CEGS Creation ‎No edit summary

14:4014:40, 6 May 2024 diff hist +1‎ CEGS Creation ‎ →‎Cleanup HACS Host Computer / Laptop: spelling
12:4412:44, 6 May 2024 diff hist +321‎ CEGS Creation ‎ Added links to the CEGS manual to the start of the procedure
12:1412:14, 6 May 2024 diff hist +35‎ CEGS Creation ‎ →‎Delivery

15:0215:02, 3 May 2024 diff hist +57‎ Plug Valve 1/4 + Actuator Creation ‎No edit summary current
15:0215:02, 3 May 2024 diff hist +57‎ Plug Valve 1/2 + Actuator Creation ‎No edit summary current
15:0015:00, 3 May 2024 diff hist +873‎ Plug Valve 1/2 + Actuator Creation ‎No edit summary
14:5814:58, 3 May 2024 diff hist +18‎ Plug Valve 1/4 + Actuator Creation ‎No edit summary
14:5714:57, 3 May 2024 diff hist +1,659‎ N Plug Valve 1/4 + Actuator Creation ‎ Created page with " =Insert the valve stem into the coupling= #Choose the plug's orientation in the coupling according to the valve's intended location in the plumbing Notes: #The actuator is pre-programmed to the closed position. #Usually, the servo connector pins should point downstream, and the plug's port-sealing O-ring should face upstream. #Thus, the port O-ring usually faces away from the servo pins. Exceptions occur when the downstream chamber volume must be minimized. #Align the h..."
14:4914:49, 3 May 2024 diff hist −167‎ CCQ Furnace Creation ‎No edit summary current
14:4214:42, 3 May 2024 diff hist +43‎ Furnace Installation ‎No edit summary current
14:2214:22, 3 May 2024 diff hist +397‎ Furnace Installation ‎No edit summary
14:1214:12, 3 May 2024 diff hist −71‎ CCQ Furnace Creation ‎No edit summary
14:0314:03, 3 May 2024 diff hist +27‎ Furnace Installation ‎No edit summary

15:1815:18, 2 May 2024 diff hist +153‎ Actuator Frame 4PV Creation ‎No edit summary
15:1415:14, 2 May 2024 diff hist +1‎ Actuator Frame 4PV Creation ‎No edit summary
12:4912:49, 2 May 2024 diff hist +12‎ Actuator Frame 4PV Creation ‎No edit summary

20:4320:43, 1 May 2024 diff hist +33‎ Actuator Frame 4PV Creation ‎No edit summary
20:0120:01, 1 May 2024 diff hist +260‎ Actuator Frame 4PV Creation ‎No edit summary

15:4515:45, 26 April 2024 diff hist −2‎ CEGS Creation ‎ →‎VTC Cold Operation
15:4415:44, 26 April 2024 diff hist +7‎ CEGS Creation ‎ →‎VTC Cold Operation

17:0117:01, 25 April 2024 diff hist +1,038‎ N O-ring bakeout Creation ‎ Created page with "O-ring bakeout Summary: Bake Viton O-rings at 150 °C under vacuum for 4 hours. Distribute the O-rings evenly in a clean borosilicate or stainless steel vessel. A dish or pan is best. A beaker may be used for smaller quantities of O-rings, but spreading the O-rings over a larger surface area is preferable. Place the O-rings into the vacuum oven and evacuate the chamber to < 7 Torr. If the bakeout vacuum system is equipped with a turbo pump and flow-through cold trap,..." current
16:0516:05, 25 April 2024 diff hist +311‎ Phase Separator Rod Creation ‎No edit summary current
15:4015:40, 25 April 2024 diff hist −39‎ Phase Separator Rod Creation ‎No edit summary
15:3015:30, 25 April 2024 diff hist +38‎ Phase Separator Rod Creation ‎No edit summary

17:2817:28, 23 April 2024 diff hist +440‎ FTC LN Line Creation ‎No edit summary current
17:2217:22, 23 April 2024 diff hist −9‎ MFV Actuator Adapter Creation ‎No edit summary current
17:2117:21, 23 April 2024 diff hist +7‎ MFV Actuator Adapter Creation ‎No edit summary
17:2117:21, 23 April 2024 diff hist +309‎ N TC Staple Creation ‎ Created page with "# Cut SS304 wire 0.025 spring back to 1.625 inches. # Grab the center of the cut wire with pliers. # Bend the wire down on both sides of the pliers. #* If the wire was centered correctly then both legs of the wire will be the same length. #* Check model to make sure that the part is made to the correct size." current
17:1717:17, 23 April 2024 diff hist +304‎ N MFV Actuator Adapter Creation ‎ Created page with "# Cut blank to .504 # Face part on the lathe # Use center bit to put a mark on part # Use .182 bit to create hole at center # Chamfer the inside edge of both sides of the hole # Ream the part with a 3/16 undersized bit # Grind .015 off the side of the part # Drill a .136 hole # Tap that hole with 8-36"
17:1317:13, 23 April 2024 diff hist +272‎ N Phase Separator Rod Creation ‎ Created page with "# Cut rod to 14.084 # Use swagelok bender # Mark the part 6.071 from the end #* We will call this section of the rod leg a # Place leg a in the bender and line up the mark on the rod with the 0 mark on the bender # Make a 90 degree bend # Check to make sure it is square"
13:4513:45, 23 April 2024 diff hist +30‎ Mains detector ‎No edit summary current
13:4213:42, 23 April 2024 diff hist 0‎ N CEGS Nameplate Creation ‎ Created blank page Tag: Visual edit

16:1116:11, 19 April 2024 diff hist −151‎ FTC Air Line Creation ‎No edit summary current

16:5816:58, 18 April 2024 diff hist +172‎ N Servo Spacer-Bearing Creation ‎ Created page with "# Place a .144 bit in the mill. # Turn the mill on then push the spacer-bearing onto the drill bit. #* MAKE SURE TO NOT TOUCH THE BIT WITH HANDS OR ANY LOOSE CLOTHING/HAIR." current

16:5516:55, 15 April 2024 diff hist −2‎ Plug Valve SS 1/4 Modified Creation ‎No edit summary current
16:5516:55, 15 April 2024 diff hist −1‎ Plug Valve SS 1/4 Modified Creation ‎No edit summary

15:1215:12, 11 April 2024 diff hist +341‎ Phase Separator Pad Creation ‎ Added procedure to use the manual mill to create the hole current

19:4519:45, 10 April 2024 diff hist +204‎ Plug Valve SS 1/4 Modified Creation ‎No edit summary
13:5713:57, 10 April 2024 diff hist +53‎ GR Bank Hinge Creation ‎No edit summary current

15 May 2024

14 May 2024

10 May 2024

9 May 2024

8 May 2024

6 May 2024

3 May 2024

2 May 2024

1 May 2024

26 April 2024

25 April 2024

23 April 2024

19 April 2024

18 April 2024

15 April 2024

11 April 2024

10 April 2024