Jump to content

LN Manifold Body 11 Port Creation: Difference between revisions

From Aeon HACS Wiki
Created page with "= Work offsets = # O0014: fence = Programs = # O0761: cover # O0762: cavity # O0763: port holes = Tooling = # T0002: 7/32 end mill, 4-flute # T0009: 0.125 drill # T0011: 0.078 end mill, 3-flute # T0015: 1/8 end mill, 2-flute # T0016: 0.25 end mill, 2-flute # T0017: 3/8 end mill, 2-flute # T0018: 1/2 end mill, 2-flute # T0021: 1 x 4 end mill, 2-flute # T0023: 0.180 drill = Stock (inches) = # Blank: 11.5 x 2.75 x 5.5 = Finished dimensions (inches) = # Lid: 11.5 x 2.75..."
 
Edited to reflect new program order + structure
 
Line 3: Line 3:


= Programs =
= Programs =
# O0761: cover
# O0751: face front+back
# O0762: cavity
# O0752: face top+bottom
# O0763: port holes
# O0753: face top
# O0761: lid
# O0762: stem holes
# O0763: drain holes
# O0764: cavity
# O0765: lid vent


= Tooling =
= Tooling =
Line 20: Line 25:


= Stock (inches) =
= Stock (inches) =
# Blank: 11.5 x 2.75 x 5.5
# Blank: 11.75 x 3.0 x 5.75


= Finished dimensions (inches) =
= Finished dimensions (inches) =
Line 27: Line 32:


= Instructions =
= Instructions =
# Reference face: left
# Reference face: right
# Run 'face front+back' on front and back faces
## Make sure the faces are as parallel and square as possible when facing sides
# Run 'face top+bottom" on top and bottom faces
## Use faced sides to make sure the top and bottom are square to the sides
# Run 'lid' on top face
# Run 'lid' on top face
# Separate lid from body using bandsaw
# Separate lid from body using bandsaw
## Part lid at 1.25"
## Part lid at 1.25"
## Size body to 4"
## Run 'face top' on top face
# Run 'cavity' on top face of 'body'
# Run 'stem holes' on back face
# Run 'stem holes' on back face of 'body'
# Run 'drain holes' on bottom face
# Run 'cavity' on top face
#* (CHECK TO SEE IF TOOL 23 HAS THE CORRECT TOOL LOADED BEFORE RUNNING THIS)
#* (CHECK TO SEE IF TOOL 23 HAS THE CORRECT TOOL LOADED BEFORE RUNNING THIS)
# Run 'drain holes' on bottom face of 'body'
# Run 'lid vent' on lid
# Run 'lid 2nd op' on right face of 'body'

Latest revision as of 14:20, 15 July 2024

Work offsets

  1. O0014: fence

Programs

  1. O0751: face front+back
  2. O0752: face top+bottom
  3. O0753: face top
  4. O0761: lid
  5. O0762: stem holes
  6. O0763: drain holes
  7. O0764: cavity
  8. O0765: lid vent

Tooling

  1. T0002: 7/32 end mill, 4-flute
  2. T0009: 0.125 drill
  3. T0011: 0.078 end mill, 3-flute
  4. T0015: 1/8 end mill, 2-flute
  5. T0016: 0.25 end mill, 2-flute
  6. T0017: 3/8 end mill, 2-flute
  7. T0018: 1/2 end mill, 2-flute
  8. T0021: 1 x 4 end mill, 2-flute
  9. T0023: 0.180 drill


Stock (inches)

  1. Blank: 11.75 x 3.0 x 5.75

Finished dimensions (inches)

  1. Lid: 11.5 x 2.75 x 1.25, w/ 0.1875 holes
  2. Body: 11.5 x 2.75 x 4.0, w/ 0.5 holes

Instructions

  1. Reference face: right
  2. Run 'face front+back' on front and back faces
    1. Make sure the faces are as parallel and square as possible when facing sides
  3. Run 'face top+bottom" on top and bottom faces
    1. Use faced sides to make sure the top and bottom are square to the sides
  4. Run 'lid' on top face
  5. Separate lid from body using bandsaw
    1. Part lid at 1.25"
    2. Run 'face top' on top face
  6. Run 'stem holes' on back face
  7. Run 'drain holes' on bottom face
  8. Run 'cavity' on top face
    • (CHECK TO SEE IF TOOL 23 HAS THE CORRECT TOOL LOADED BEFORE RUNNING THIS)
  9. Run 'lid vent' on lid