All public logs

Combined display of all available logs of Aeon HACS Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

14:09, 15 August 2024 Ohusok talk contribs created page SS316 EP Tubing Creation (Created page with "# Use the model to create a list of the needed tube types and their numbers. #*The two most used tube sizes are 1/4 inch and 1/2 inch diameter, the process is the same for both sizes but the tools and programs used will be different. ====Cut tubing==== # Grab the correct tubing from the shelf. #* If using a new piece of stock, use rubbing alcohol to wipe away the factory lettering on the metal. #* If the stock has already been used, check that it is the right type by l...")
15:56, 13 August 2024 Ohusok talk contribs created page CEGS Cables (Created page with "==Cut Cables and Wire Connectors== Cable Groups * Front Bar * Back Bar * VM * LN Manifold Cable Types * Valve actuators * Pressure sensors * Thermocouples ** Type T ** Type K (furnaces) * Control wires ** Heater control wires ** Solenoid valves * Grounding wires <br> # Determine the cable lengths, cut them to length #* Use standardized distances to make measuring consistent. #* Include excess length for all cables to allow for service relief...")
12:57, 13 August 2024 Ohusok talk contribs created page LN Tube Sleeve Creation (Created page with "Before removing the LN tube from the system, mark the length needed for the tube sleeve # with the LN tubes in the "up" position, mark 0.25 in away from the bottom the bottom of the IPS stop # measure the distance from the end of the tube to 0.25 in outside for the tube grip at the GR FTC. Mark this distance on a piece of tape or on a ruler. Do not mark the LN tube, this distance will be the same for all tubes. Measure a piece of tubular shoelace black 7/16 # Push the...")
12:10, 13 August 2024 Ohusok talk contribs created page LN Tube Sleeve (Created page with "{{Item navbar |creation= LN+Tube+Sleeve+Creation |product= LN+tube+sleeve+250 }}")
10:52, 13 August 2024 Ohusok talk contribs created page Pressure Sensors Creation (Created page with "{{Item navbar |model= |creation= |product=}} ==Pressure Sensor Cables== # Strip the cable housing back long enough that the housing is flush with the bottom of the pin but does not get crimped with the wire. #* Use the appropriate pin-crimping tool for the given size of pin. # Identify orientation of the DSUB shell and the needed channels. # Push DSUB contact all the way into DSUB shell. #*crimp the contact tighter with flat pliers if the pin does not easily push into th...")
10:38, 13 August 2024 Ohusok talk contribs created page Pressure Sensors (Created page with "{{Item navbar |model= |creation=Pressure_Sensors_Creation |product=}}")
15:53, 6 August 2024 Ohusok talk contribs created page Ion Gauge Cable Adapter Creation (Created page with "{{Item navbar |model= |about=Ion_Gauge_Cable_Adapter_Creation |product=ion+gauge+cable+adapter}} # Cut a 3 inch piece of CAT5e cable # Push the wires through the cable housing so that they stick out enough to work with #* Remove the piece of fiber from the wire bundle #* Note that there are 4 color pairs, orange, green, blue, and brown, each twisted around a white wire. # The Blue, Green and Brown wires are not attached to the molex housing, cut them back about 1/2 inch....")
15:10, 6 August 2024 Ohusok talk contribs created page Ion Gauge Cable Adapter (Created page with "{{Item navbar |model= |creation=Ion_Gauge_Cable_Adapter_Creation |product=ion+gauge+cable+adapter}}")
15:30, 30 July 2024 Ohusok talk contribs created page V-wheel spacer (Created page with "# Take an aluminum spacer 192x500x562 and chuck it up in the TL-1 with 0.25 in stickout. # Follow all directions within the V-wheel spacer program. # Deburr any rough edges with the buffing wheel.") Tag: Visual edit: Switched
13:23, 30 July 2024 Ohusok talk contribs created page GR hinge mount Creation (Created page with "# Widen the hinge hole using a 3/8 in oversize reamer. # Tap the holes for the GR swing stops with a 6/32 bit.")
13:18, 30 July 2024 Ohusok talk contribs created page GR hinge mount (Created page with "{{Item navbar |model=https://cad.onshape.com/documents/1baa9c5a7bb6f5309dbb3620/v/394461d63e9dfc4450ae5291/e/1616bc8c19fe94eef3965aa1?renderMode=0&uiState=66a94a7a3f085e628572fa0f |creation=GR_hinge_mount_Creation |product=GR+hinge+mount}}")
11:54, 30 July 2024 Ohusok talk contribs created page FTC Thermocouple Installation (Created page with "FTC TC-T General Installation Instructions <br> # Take the TC-T cable cut for the FTC you are working on. Check that the end of the cable has been cut to the appropriate length for the given FTC. #* LN Manifold TC ends are 5/8 in #* All other TC ends are 3/8 in # TC-T Economy wires are very easily twisted. Flatten out the wire by pressing it between two flat surfaces, then coil it up. This will make routing the wire on the frame easier. # Use the TC bending tool TL-TCB t...")
16:47, 25 July 2024 Ohusok talk contribs created page CFF Repair (Created page with "==CFF Repair== If the ceramic fiber furnace is damaged, it is possible to patch the outside using a mixture of hot surface mix, ceramic fiber rigidizer, and ceramic fiber blanket. # Prepare the damaged area by removing loose or out of place fibers. # Soak the area with rigidizer. # Take a piece of ceramic fiber blanket and manipulate it to fill the damaged area. #* Use small pieces at a time, creating layers. Add rigidizer to each layer. # Dust each layer with hot surf...")
16:55, 4 June 2024 Ohusok talk contribs created page File:Carriage and plate tabs distance.png
16:55, 4 June 2024 Ohusok talk contribs uploaded File:Carriage and plate tabs distance.png
16:52, 4 June 2024 Ohusok talk contribs created page File:Carriage end plate tabs .png
16:52, 4 June 2024 Ohusok talk contribs uploaded File:Carriage end plate tabs .png
16:10, 28 May 2024 Ohusok talk contribs created page CEGS Frame (Created blank page) Tag: Visual edit: Switched