VTC Creation: Difference between revisions
(Added instruction info, markup lang, link nav bar, updated 3d model and product info links; about this item still pending, pending instructional images) |
mNo edit summary |
||
Line 4: | Line 4: | ||
|product=VTC}} | |product=VTC}} | ||
VTC Assembly | VTC Assembly | ||
TC=thermocouple | TC=thermocouple | ||
# VTC heater assembly bend the TC-T FEP 3x60 using the | # VTC heater assembly bend the TC-T FEP 3x60 using the thermocouple bender (TL-TCB) | ||
# Make a first bend on the line indicated by the tool, with the red wire facing up use a wooden block to push the | # Make a first bend on the line indicated by the tool, with the red wire facing up use a wooden block to push the thermocouple against the metal rod so that it creates a sharp turn turn the thermocouple 180 degrees. | ||
# Make a second bend use the technique that was previously mentioned to make the bend in the end. | # Make a second bend use the technique that was previously mentioned to make the bend in the end. | ||
#* There should be two 90 degree bends that create an S shape. | #* There should be two 90 degree bends that create an S shape. | ||
Line 18: | Line 18: | ||
#* Check the model to properly orientate the TC-T FEP. | #* Check the model to properly orientate the TC-T FEP. | ||
# Take a TC-T economy cable and place it to the right of the TC-T FEP so that the red wires on both are facing the same direction. | # Take a TC-T economy cable and place it to the right of the TC-T FEP so that the red wires on both are facing the same direction. | ||
# Slide the 1 inch piece of heatshrink over the | # Slide the 1 inch piece of heatshrink over the thermocouple s. | ||
# Very gently heat it to the point where it is loosely holding the cables. | # Very gently heat it to the point where it is loosely holding the cables. | ||
#* Adjust the blue cable such that the junction is 0.71 in from the bottom edge of the conduit cup. | #* Adjust the blue cable such that the junction is 0.71 in from the bottom edge of the conduit cup. | ||
Line 26: | Line 26: | ||
# Then insert the heater into the VTT. [IMAGE] | # Then insert the heater into the VTT. [IMAGE] | ||
# Align the heater so that the cables rest in the notch at the top of the VTC body. | # Align the heater so that the cables rest in the notch at the top of the VTC body. | ||
# Check that the orientation has the blue | # Check that the orientation has the blue thermocouple cable on the right, the white conduit wires on the left, and the metal thermocouple in the middle. | ||
# Bend a second TC-T 90 degrees at the junction insert the TC-T into the cup of the heater. | # Bend a second TC-T 90 degrees at the junction insert the TC-T into the cup of the heater. | ||
# Ziptie the TC-T to the other | # Ziptie the TC-T to the other thermocouple wires shape .5 grams of copper wool around a culture tube quartz 12 x 75 mm. | ||
# Slowly push the cooper wool into the cup of the heater. | # Slowly push the cooper wool into the cup of the heater. | ||
# Place transfer tape on the lid of the VTC. | # Place transfer tape on the lid of the VTC. |
Revision as of 10:11, 24 February 2024
VTC Assembly TC=thermocouple
- VTC heater assembly bend the TC-T FEP 3x60 using the thermocouple bender (TL-TCB)
- Make a first bend on the line indicated by the tool, with the red wire facing up use a wooden block to push the thermocouple against the metal rod so that it creates a sharp turn turn the thermocouple 180 degrees.
- Make a second bend use the technique that was previously mentioned to make the bend in the end.
- There should be two 90 degree bends that create an S shape.
- Find or make 3 of the TC-T economy.
- These wires should have been made when cutting all of the wires for the system.
- The TC-T economy should be at least as long as the TC-T FE.
- Cut a 1 inch piece of heatshrink 2:1 clear 1 place the heatshrink on the VTT heater heatshrink sizer.
- Carefully heat the folded edges so that it becomes circular.
- The heatshrink should be mostly round but it shouldn't grip the sizer.
- Place the TC-T FEP into the small hole at the bottom of a completed VTC thermal conduit (MP-VTCTHCND).
- Check the model to properly orientate the TC-T FEP.
- Take a TC-T economy cable and place it to the right of the TC-T FEP so that the red wires on both are facing the same direction.
- Slide the 1 inch piece of heatshrink over the thermocouple s.
- Very gently heat it to the point where it is loosely holding the cables.
- Adjust the blue cable such that the junction is 0.71 in from the bottom edge of the conduit cup.
- Heat the heatshrink to hold both TC.
- Inserting the heater into the VTC body align the TC-T economy with the hole that it will go through. [IMAGE]
- First use the bottom side of the VTT to line up the TC. [IMAGE]
- Then insert the heater into the VTT. [IMAGE]
- Align the heater so that the cables rest in the notch at the top of the VTC body.
- Check that the orientation has the blue thermocouple cable on the right, the white conduit wires on the left, and the metal thermocouple in the middle.
- Bend a second TC-T 90 degrees at the junction insert the TC-T into the cup of the heater.
- Ziptie the TC-T to the other thermocouple wires shape .5 grams of copper wool around a culture tube quartz 12 x 75 mm.
- Slowly push the cooper wool into the cup of the heater.
- Place transfer tape on the lid of the VTC.
- Press the lid onto the body of the VTC upper.
- Place transfer tape on the top of the body of the VTC lower
- Trim the transfer tape so that it does not hang over any empty gaps.
- Press the body of the VTC upper into the body of the VTC lower
- Ziptie the wires together.